H6-type Single Phase Full-Bridge PV Grid-Tied Transformerless Inverters

ABSTRACT:

Photovoltaic (PV) generation systems are widely employed in transformer less inverters, in order to achieve the benefits of high efficiency and low cost. Safety requirements of leakage currents are met by proposing the various transformers less inverter topologies. In this paper, three transformer less inverter topologies are illustrated such as a family of H6 transformer less inverter topologies with low leakage currents is proposed, and the intrinsic relationship between H5 topology, highly efficient and reliable inverter concept (HERIC) topology. The proposed H6 topology has been discussed as well. For a detailed analysis with operation modes and modulation strategy one of the proposed H6 inverter topologies is taken as an example. Comparison among the HERIC, the H5, and the proposed H6 topologies is been done for the power device costs and power losses. For evaluating their performances in terms of power efficiency and leakage currents characteristics, a universal prototype is built for these three topologies mentioned. Simulation results show that the proposed HERIC topology and the H6 topology achieve similar performance in leakage currents, which is slightly worse than that of the H5 topology, but it features higher efficiency than that of H5 topology.

KEYWORDS:

1.      Common-mode voltage

2.       Grid-tied inverter

3.       Leakage current

4.       Photovoltaic (PV) generation system

5.       Transformerless inverter

SOFTWARE: MATLAB/SIMULINK

BLOCK DIAGRAM:

Fig. 1. Leakage current path for transformerless PV inverters

EXPECTED SIMULATION RESULTS:

Fig. 2. CM voltage and leakage current in H6 topology. (a) CM voltage. (b) Leakage current.

Fig. 3. Drain–source voltages in H6 topology. (a) Voltage stress on S5 and S6 . (b) Detailed waveforms.

Fig. 4. DM characteristic of H6 topology.

Fig. 5. Efficiency comparison of H5, HERIC and H6 topologies.

             

CONCLUSION:

In this paper, based on the H5 topology, a new current path is formed by inserting a power device between the terminals of PV array and the midpoint of one of bridge legs. As a result, a family of single-phase transformerless full-bridge H6 inverter topologies with low leakage currents is derived. The proposed H6 topologies have the following advantages and evaluated by simulation results:

1) The conversion efficiency of the novel H6 topology is better than that of the H5 topology, and its thermal stress distribution is better than that of the H5 topology;

2) The leakage current is almost the same as HERIC topology, and meets the safety standard;

3) The excellent DM performance is achieved like the isolated full-bridge inverter with uniploar SPWM. Therefore, the proposed H6 topologies are good solutions for the single phase transformerless PV grid-tied inverters.

 REFERENCES:

 [1] S. B. Kjaer, J. K. Pederson, and F. Blaabjerg, “A review of single-phase grid-connected inverters for photovoltaic modules,” IEEE Trans. Ind. Appl., vol. 41, no. 5, pp. 1292–1306, Sep/Oct. 2005.

[2] F. Blaabjerg, Z. Chen, and S. B. Kjaer, “Power electronics as efficient interface in dispersed power generation systems,” IEEE Trans. Power Electron., vol. 19, no. 5, pp. 1184–1194, Sep. 2004.

[3] B. Sahan, A. N. Vergara, N. Henze, A. Engler, and P. Zacharias, “A single stage PVmodule integrated converter based on a low-power current source inverter,” IEEE Trans. Ind. Electron., vol. 55, no. 7, pp. 2602–2609, Jul.2008.

[4] M. Calais, J. Myrzik, T. Spooner, and V. G. Agelidis, “Inverters for single phase grid connected photovoltaic systems—An overview,” in Proc. IEEE PESC, 2002, vol. 2, pp. 1995–2000.

[5] F. Blaabjerg, Z. Chen, and S. B. Kjaer, “Power electronics as efficient interface in dispersed power generation systems,” IEEE Trans. Power Electron., vol. 19, no. 5, pp. 1184–1194, Sep. 2004.

A Unified Control Strategy for Three-Phase Inverter in Distributed Generation

ABSTRACT:

This paper presents a unified control strategy that enables both islanded and grid-tied operations of three-phase inverter in distributed generation, with no need for switching between two corresponding controllers or critical islanding detection. The proposed control strategy composes of an inner inductor current loop, and a novel voltage loop in the synchronous reference frame. The inverter is regulated as a current source just by the inner inductor current loop in grid-tied operation, and the voltage controller is automatically activated to regulate the load voltage upon the occurrence of islanding. Furthermore, the waveforms of the grid current in the grid-tied mode and the load voltage in the islanding mode are distorted under nonlinear local load with the conventional strategy. And this issue is addressed by proposing a unified load current feedforward in this paper. Additionally, this paper presents the detailed analysis and the parameter design of the control strategy. Finally, the effectiveness of the proposed control strategy is validated by the simulation results.

KEYWORDS:

1.      Distributed generation (DG)

2.      Islanding

3.      Load current

4.      Seamless transfer

5.      Three-phase inverter

6.       Unified control

SOFTWARE: MATLAB/SIMULINK

BLOCK DIAGRAM:

Fig. 1. Overall block diagram of the proposed unified control strategy.

EXPECTED SIMULATION RESULTS:

Fig. 2. Simulation waveforms of load voltage v_{C a} , grid current i_ga, and inductor current i_La when DG is in the grid-tied mode under condition of the step down of the grid current reference from 9 A to 5 A with: (a) conventional

voltage mode control, and (b) proposed unified control strategy.

Fig. 3. Simulation waveforms of load voltage v_{C a} , grid current i_ga, and inductor current i_La when DG is transferred from the grid-tied mode to the islanded mode with: (a) conventional hybrid voltage and current mode control, and (b) proposed unified control strategy.

CONCLUSION:

A unified control strategy was proposed for three-phase inverter in DG to operate in both islanded and grid-tied modes, with no need for switching between two different control architectures or critical islanding detection. A novel voltage controller was presented. It is inactivated in the grid-tied mode, and the DG operates as a current source with fast dynamic performance. Upon the utility outage, the voltage controller can automatically be activated to regulate the load voltage. Moreover, a novel load current feed forward was proposed, and it can improve the waveform quality of both the grid current in the grid-tied mode and the load voltage in the islanded mode. The proposed unified control strategy was verified by the simulation results.

REFERENCES:

 [1] R. C. Dugan and T. E. McDermott, “Distributed generation,” IEEE Ind. Appl. Mag., vol. 8, no. 2, pp. 19–25, Mar./Apr. 2002.

[2] R. H. Lasseter, “Microgrids and distributed generation,” J. Energy Eng., vol. 133, no. 3, pp. 144–149, Sep. 2007.

[3] C. Mozina, “Impact of green power distributed generation,” IEEE Ind. Appl. Mag., vol. 16, no. 4, pp. 55–62, Jul./Aug. 2010.

[4] IEEE Recommended Practice for Utility Interface of Photovoltaic(PV) Systems, IEEE Standard 929-2000, 2000.

[5] IEEE Standard for Interconnecting Distributed Resources with Electric Power Systems, IEEE Standard 1547-2003, 2003.

A Switched-Capacitor Inverter Using Series/Parallel Conversion with Inductive Load

ABSTRACT

A novel switched-capacitor inverter is proposed. The proposed inverter outputs larger voltage than the input voltage by switching the capacitors in series and in parallel. The maximum output voltage is determined by the number of the capacitors. The proposed inverter, which does not need any inductors, can be smaller than a conventional two-stage unit which consists of a boost converter and an inverter bridge. Its output harmonics are reduced compared to a conventional voltage source single phase full bridge inverter. In this paper, the circuit configuration, the theoretical operation, the simulation results with MATLAB/ SIMULINK, and the experimental results are shown. The experimental results accorded with the theoretical calculation and the simulation results.

KEYWORDS

1.      Charge pump

2.       Multicarrier PWM

3.       Multilevel Inverter

4.       Switched capacitor (SC)

SOFTWARE: MATLAB/SIMULINK

 BLOCK DIAGRAM:

Fig. 1. Circuit topology of the switched-capacitor inverter using series/ parallel conversion.

EXPECTED SIMULATION RESULTS

Fig. 2. Simulated voltage waveforms of the proposed inverter (n = 2) designed for high power at 4.50 [kW], switching frequency f = 40 [kHz] and reference waveform frequency fref = 1 [kHz]. (a) Bus voltage waveform vbus and (b) the output voltage waveform vout.

Fig. 3. Simulated current waveforms of the capacitor iC1 in the proposed inverter (n = 2).(a) Designed for low power at 5.76 [W] and (b) designed for high power at 4.50 [kW].

Fig. 4. Simulated spectra of the bus voltage waveform of the proposed inverters (n = 2) normalized with the fundamental component. (a) Designed for low power at 5.76 [W] and (b) designed for high power at 4.50 [kW].

Fig. 5. Simulated bus voltage waveforms vbus and the voltage waveforms of the load resistance vR of the proposed inverter (n = 2) designed for low power at 5.76 [W] with an inductive load.

Fig. 6. Experimental circuit

Fig. 7. Observed bus voltage waveform vbus. Vertical 10 [V/div], horizontal

250 [μs/div].

Fig. 8. Observed output voltage waveform vout. Vertical 10 [V/div],

horizontal 250 [μs/div].

Fig. 9. Observed spectrum of the bus voltage waveform.

Fig. 10. Observed current waveform of the capacitor iC1. Vertical 500 [mA/div], horizontal 250 [μs/div]

Fig. 11. Observed voltage waveforms vbus and vR with an inductive load.

Vertical 10 [V/div], horizontal 250 [μs/div].

CONCLUSION

In this paper, a novel boost switched-capacitor inverter was proposed. The circuit topology was introduced. The modulation method, the determination method of the capacitance, and the loss calculation of the proposed inverter were shown. The circuit operation of the proposed inverter was confirmed by the simulation results and the experimental results with a resistive load and an inductive load. The proposed inverter outputs a larger voltage than the input voltage by switching the capacitors in series and in parallel. The inverter can operate with an inductive load. The structure of the inverter is simpler than the conventional switched-capacitor inverters. THD of the output waveform of the inverter is reduced compared to the conventional single phase full bridge inverter as the conventional multilevel inverter.

REFERENCES

[1] H. Liu, L. M. Tolbert, S. Khomfoi, B. Ozpineci, and Z. Du, “Hybrid cascaded multilevel inverter with PWM control method,” in Proc. IEEE Power Electron. Spec. Conf., Jun. 2008, pp. 162–166.

[2] A. Emadi, S. S. Williamson, and A. Khaligh, “Power electronics intensive solutions for advanced electric, hybrid electric, and fuel cell vehicular power systems,” IEEE Trans. Power Electron., vol. 21, no. 3, pp. 567–577, May 2006.

[3] L. G. Franquelo, J. Rodriguez, J. I. Leon, S. Kouro, R. Portillo, and M. A. M. Prats, “The age of multilevel converters arrives,” IEEE Ind. Electron. Mag., vol. 2, no. 2, pp. 28–39, Jun. 2008.

[4] Y. Hinago and H. Koizumi, “A single phase multilevel inverter using switched series/parallel DC voltage sources,” IEEE Trans. Ind. Electron., vol. 57, no. 8, pp. 2643–2650, Aug. 2010.

[5] S. Chandrasekaran and L. U. Gokdere, “Integrated magnetics for interleaved DC–DC boost converter for fuel cell powered vehicles,” in Proc. IEEE Power Electron. Spec. Conf., Jun. 2004, pp. 356–361.

[6] Y. Hinago and H. Koizumi, “A switched-capacitor inverter using series/ parallel conversion,” in Proc. IEEE Int. Symp. Circuits Syst., May/Jun. 2010, pp. 3188–3191.

[7] J. A. Starzyk, Y. Jan, and F. Qiu, “A dc–dc charge pump design based on voltage doublers,” IEEE Trans. Circuits Syst. I, Fundam. Theory Appl., vol. 48, no. 3, pp. 350–359, Mar. 2001.

[8] M. R. Hoque, T. Ahmad, T. R. McNutt, H. A. Mantooth, and M. M. Mojarradi, “A technique to increase the efficiency of high-voltage charge pumps,” IEEE Trans. Circuits Syst. II, Exp. Briefs, vol. 53, no. 5, pp. 364–368, May 2006.

[9] O. C.Mak and A. Ioinovici, “Switched-capacitor inverter with high power density and enhanced regulation capability,” IEEE Trans. Circuits Syst. I, Fundam. Theory Appl., vol. 45, no. 4, pp. 336–347, Apr. 1998.

[10] B. Axelrod, Y. Berkovich, and A. Ioinovici, “A cascade boost-switchedcapacitor- converter-two level inverter with an optimized multilevel output waveform,” IEEE Trans. Circuits Syst. I, Reg. Papers, vol. 52, no. 12, pp. 2763–2770, Dec. 2005.

[11] J. I. Rodriguez and S. B. Leeb, “A multilevel inverter topology for inductively coupled power transfer,” IEEE Trans. Power Electron., vol. 21, no. 6, pp. 1607–1617, Nov. 2006.

[12] X. Kou, K. A. Corzine, and Y. L. Familiant, “A unique fault-tolerant design for flying capacitor multilevel inverter,” IEEE Trans. Power Electron., vol. 19, no. 4, pp. 979–987, Jul. 2004.

[13] S. Lu, K. A. Corzine, andM. Ferdowsi, “A unique ultracapacitor direct integration scheme in multilevel motor drives for large vehicle propulsion,” IEEE Trans. Veh. Technol., vol. 56, no. 4, pp. 1506–1515, Jul. 2007.

[14] J. I. Leon, S. Vazquez, A. J. Watson, L. G. Franquelo, P. W. Wheeler, and J. M. Carrasco, “Feed-forward space vector modulation for single-phase multilevel cascaded converters with any dc voltage ratio,” IEEE Trans. Ind. Electron., vol. 56, no. 2, pp. 315–325, Feb. 2009.

[15] B. P. McGrath and D. G. Holmes, “Multicarrier PWM strategies for multilevel inverters,” IEEE Trans. Ind. Electron., vol. 49, no. 4, pp. 858–867, Aug. 2002.

[16] R. Gupta, A. Ghosh, and A. Joshi, “Switching characterization of cascaded multilevel-inverter-controlled systems,” IEEE Trans. Ind. Electron., vol. 55, no. 3, pp. 1047–1058, Mar. 2008.

[17] J. Zhang, Y. Zou, X. Zhang, and K. Ding, “Study on a modified multilevel cascade inverter with hybrid modulation,” in Proc. IEEE Power Electron. Drive Syst., Oct. 2001, pp. 379–383.

[18] V. G. Agelidis, A. I. Balouktsis, and C. Cossar, “On attaining the multiple solutions of selective harmonic elimination PWM three-level waveforms through function minimization,” IEEE Trans. Ind. Electron., vol. 55, no. 3, pp. 996–1004, Mar. 2008.

[19] J. A. Pontt, J. R. Rodriguez, A. Liendo, P. Newman, J. Holtz, and J. M. San Martin, “Network-friendly low-switching-frequency multipulse high-power three-level PWM rectifier,” IEEE Trans. Ind. Electron., vol. 56, no. 4, pp. 1254–1262, Apr. 2009.

[20] M. K. Kazimierczuk, “Switching losses with linear MOSFET output capacitance,” in Pulse-Width Modulated DC–DC Power Converters, 1st ed. West Sussex, U.K.: Wiley, 2008, ch. 2, pp. 37–38, sec. 2.

An Advanced Power Electronics Interface for Electric Vehicles Applications

Abstract

Power electronics interfaces play an increasingly important role in the future clean vehicle technologies. This paper proposes a novel integrated power electronics interface (IPEI) for battery electric vehicles (BEVs) in order to optimize the performance of the power train. The proposed IPEI is responsible for the power-flow management for each operating mode. In this paper, an IPEI is proposed and designed to realize the integration of the dc/dc converter, on-board battery charger, and dc/ac inverter together in the BEV power train with high performance. The proposed concept can improve the system efficiency and reliability, can reduce the current and voltage ripples, and can reduce the size of the passive and active components in the BEV drive trains compared to other topologies. In addition, low electromagnetic interference and low stress in the power switching devices are expected. The proposed topology and its control strategy are designed and analyzed by using MATLAB/Simulink. The simulation results related to this research are presented and discussed. Finally, the proposed topology is experimentally validated with results obtained from the prototypes that have been built and integrated in our laboratory based on TMS320F2808 DSP.

Keywords

1.      Battery electric vehicles (BEVs)

2.      interleaved dc/dc converter

3.       on-board battery charger

4.      Power train control strategies

5.       Power train modeling

6.       small-signal model

Software: MATLAB/SIMULINK

Block Diagram:

Fig. 1. Schematic diagram of the battery electric vehicles.

Expected Simulation Results:

Fig2. Dynamic performance of the battery pack and the proposed IPEI (simulation result).

Fig3. Comparative efficiency of the ac drive system (Motor & ESI) in the

proposed powertrain (simulation result).

Fig4. Efficiencies of the power electronics interfaces in the proposed power train

(simulation result).

Fig5. Power train efficiency without including the battery efficiency (simulation

result).

Conclusion

In this paper, a novel integrated power electronic interface has been proposed for BEVs to optimize the performance of the powertrain. The proposed IPEI combines the features of the BMDIC and the ESI. The proposed IPEI and its performance characteristics have been analyzed and presented. Different control strategies are designed to verify the performance of the proposed IPEI during different operating modes. It should be pointed out that the IFOC based on PWM voltage and PSO is more efficient than IFOC based on PWM voltage which is used to drive the EM during traction and braking modes. Moreover, the proposed IPEI can achieve a high power factor correction, and can achieve a low THD for the input current during charging mode from the ac grid. As is clear from the simulation results, the proposed IPEI can reduce the current and voltage ripples, can improve the efficiency and reliability, and can provide a compact size for the BEV power train. Furthermore, the battery lifespan can be increased due to the ripple reduction. Finally, the simulation and experimental results have demonstrated that the proposed IPEI has been successfully realized and it promises significant savings in component count with high performance for BEVs compared to other topologies. Therefore, it can be expected that these topologies can be utilized for development of high efficiency BEV power trains.      

References:

[1] C. C. Chan, A. Bouscayrol, and K. Chen, “Electric, hybrid, and fuel-cell vehicles: Architectures and modeling,” IEEE Trans. Veh. Technol., vol. 59, no. 2, pp. 589–598, Feb. 2010.

[2] C. C. Chan, “The state of the art of electric and hybrid, and fuel cell vehicles,” Proc. IEEE, vol. 95, no. 4, pp. 704–718, Apr. 2007.

[3] A. Emadi, S. S.Williamson, and A. Khaligh, “Power electronics intensive solutions for advanced electric, hybrid electric, and fuel cell vehicular power systems,” IEEE Trans. Power Electron., vol. 21, no. 3, pp. 567– 577, May 2006. electronics and motor drives in electric, hybrid electric, and plug-in hybrid electric vehicles,” IEEE Trans. Ind. Electron, vol. 55, no. 6, pp. 2237–2245, Jun. 2008.

[4] A. Emadi, Y. J. Lee, and K. Rajashekara, “Power

[5] S. S. Raghavan, O. C. Onar, and A. Khaligh, “Power electronic interfaces for future plug-in transportation systems,” IEEE Power Electron. Soc. Newsletter, vol. 23, Third Quarter 2010.

Comparative Analysis of LCL Filter with Active and Passive Damping Methods for Grid-interactive Inverter System

ABSTRACT:

This paper presents the control strategy for a three phase LCL-filter type based grid connected inverter system for photovoltaic (PV) applications. The control strategy proposed in the paper involves the independent control of active and reactive power injected into the grid during steady state and transient conditions. In addition to that, a comparative study between active and passive damping configurations for LCL type filter resonance damping is also analyzed. The control strategy implemented on a three-phase grid connected PV inverter is studied and verified by computer simulation based on MATLAB Simulink and the results are analyzed for effectiveness of the study.

KEYWORDS:

1.      Renewable Energy Source (RES)

2.       LCL-Filter

3.      Proportional-Resonant (PR) Controller

4.      Active damping

5.      Passive damping

SOFTWARE: MATLAB/SIMULINK

SCHEMATIC DIAGRAM:

Fig.1. Schematic diagram of grid-connected inverter system with LCL filter

CONTROL DIAGRAM:

Fig.2. Over all control strategy of Grid-connected PWM VSI

EXPECTED SIMULATION RESULTS:

Fig.3. Simulation results for active damping method under steady state condition (a) grid voltage and grid Current waveforms (b) d and q-axis grid currents (c) response of active and reactive Power (d) response of dc-link voltage (e) THD of grid current.

Fig.4. Simulation results for passive damping method under steady state condition (a) grid voltage and grid Current waveforms (b) d and q-axis grid currents (c) response of active and reactive Power (d) response of dc-link voltage (e) THD of grid current.

Fig.5. Simulation results for active damping method during step change in the input PV power (a) step change in the input PV power (b) d and q-axis grid currents (c) response of dc-link voltage (d) THD of grid current

Fig.6. Simulation results for passive damping method during step change in the input PV power (a) d and q-axis grid currents (b) response of dc-link voltage (c) THD of grid current.

             

CONCLUSION:

The paper discusses the control strategy for gridconnected PWM VSI with LCL-type filter. The advantage feature of PR controller is the possibility of implementing harmonic compensator without interfering with control dynamics, achieving a high quality delivered current are explored. In addition, a comparative study has been made between active and passive damping methods to damp-out the LCL-filter resonance. From the above said discussions, it is found that active damping method is better than passive damping method to inject sinusoidal current into the grid with less THD. Also it ensures zero steady state error with stable response. In addition to that, passive damping method involves extra cost and losses due to additional circuit components. Nevertheless, active damping method difficult to implement, but overall performance of grid-connected PWM VSI is improved with higher efficiency

REFERENCES:

[1] O.Siddique, “The Green Grid: Energy Savings and Carbon Emission Reductions Enabled by a Smart Grid,” EPRI Palo Alto, CA: 2008

[2] F. Blaabjerg, Z. Chen, and S. Kjaer, “Power electronics as efficient interface in dispersed power generation systems,” IEEE Trans. Power Electron vol. 19, no. 5, pp. 1184–1194, Sep. 2004

[3] Bochuan Liu; Byeong-Mun Song, "Modeling and analysis of an LCL filter for grid-connected inverters in wind power generation systems," In Proc. 2011 IEEE Power and Energy Society General Meeting, , pp.1-6, July 2011.

[4] Wenqiang Zhao; Guozhu Chen, "Comparison of active and passive damping methods for application in high power active power filter with LCL-filter," In Proc. International Conference on Sustainable Power Generation and Supply, 2009. SUPERGEN '09. pp.1-6, April 2009.

[5] Hoff, B.; Sulkowski, W., "Grid connected VSI with LCL filter — Models and comparison," In. Proc. 2012 IEEE Energy Conversion Congress and Exposition (ECCE), pp.4635,4642, Sept. 2012.