Design of External Inductor for Improving Performance of Voltage Controlled DSTATCOM

ABSTRACT:

A distribution static compensator (DSTATCOM) is used for load voltage regulation and its performance mainly depends upon the feeder impedance and its nature (resistive, inductive, stiff, non-stiff). However, a study for analyzing voltage regulation performance of DSTATCOM depending upon network parameters is not well defined. This paper aims to provide a comprehensive study of design, operation, and flexible control of a DSTATCOM operating in voltage control mode. A detailed analysis of the voltage regulation capability of DSTATCOM under various feeder impedances is presented. Then, a benchmark design procedure to compute the value of external inductor is presented. A dynamic reference load voltage generation scheme is also developed which allows DSTATCOM to compensate load reactive power during normal operation, in addition to providing voltage support during disturbances. Simulation and experimental results validate the effectiveness of the proposed scheme.

KEYWORDS :

      1.      Distribution static compensator (DSTATCOM)

2.      Current control

3.      Voltage control

4.      Power factor

5.      Power quality

SOFTWARE: MATLAB/SIMULINK

EQUIVALENT CIRCUIT DIAGRAM:

Fig. 1. Three phase equivalent circuit of DSTATCOM topology in distribution system.

 EXPECTED SIMULATION RESULTS:

Fig. 2. Voltage regulation performance of conventional DSTATCOM with resistive feeder. (a) PCC voltages. (b) Load Voltages. (c) Source currents. (d) Filter currents. (e) Load currents.

Fig. 3. Simulation results. (a) During normal operation (i)-(v). (b) During voltage sag (vi)-(x). (c) During voltage swell (xi)-(xv).

CONCLUSION:

This paper has presented design, operation, and control of a DSTATCOM operating in voltage control mode (VCM). After providing a detailed exploration of voltage regulation capability of DSTATCOM under various feeder scenarios, a benchmark design procedure for selecting suitable value of external inductor is proposed. An algorithm is formulated for dynamic reference load voltage magnitude generation. The DSTATCOM has improved voltage regulation capability with a reduced current rating VSI, reduced losses in the VSI and feeder. Also, dynamic reference load voltage generation scheme allows DSTATCOM to set different constant reference voltage during voltage disturbances. Simulation and experimental results validate the effectiveness of the proposed solution. The external inductor is a very simple and cheap solution for improving the voltage regulation, however it remains connected throughout the operation and continuous voltage drop across it occurs. The future work includes operation of this fixed inductor as a controlled reactor so that its effect can be minimized by varying its inductance.

REFERENCES:

[1] M. H. Bollen, Understanding power quality problems. vol. 3, IEEE press New York, 2000.

[2] S. Ostroznik, P. Bajec, and P. Zajec, “A study of a hybrid filter,” IEEE Trans. Ind. Electron., vol. 57, no. 3, pp. 935–942, Mar. 2010.

[3] C. Kumar and M. Mishra, “A voltage-controlled DSTATCOM for power quality improvement,” IEEE Trans. Power Del., vol. 29, no. 3, pp. 1499– 1507, June 2014.

[4] Q. Liu, L. Peng, Y. Kang, S. Tang, D. Wu, and Y. Qi, “A novel design and optimization method of an LCL filter for a shunt active power filter,” IEEE Trans. Ind. Electron., vol. 61, no. 8, pp. 4000–4010, Aug. 2014.

[5] T. Aziz, M. Hossain, T. Saha, and N. Mithulananthan, “VAR planning with tuning of STATCOM in a DG integrated industrial system,” IEEE Trans. Power Del., vol. 28, no. 2, pp. 875–885, Apr. 2013.

Dynamic voltage restorer employing multilevel cascaded H-bridge inverter

ABSTRACT

This study presents design and analysis of a dynamic voltage restorer (DVR) which employs a cascaded multilevel inverter with capacitors as energy sources. The multilevel inverter enables the DVR to connect directly to the medium voltage networks, hence, eliminating the series injection transformer. Using zero energy compensation method, the DVR does not need active energy storage systems, such as batteries. Since the energy storage system only includes capacitors, the control system will face some additional challenges compared with other DVR systems. Controlling the voltage of capacitors around a reference voltage and keeping the balance between them, in standby and compensation period, is one of them. A control scheme is presented in this study that overcomes the challenges. Additionally, a fast three-phase estimation method is employed to minimise the delay of DVR and to mitigate the voltage sags as fast as possible. Performance of the control scheme and estimation method is assessed using several simulations in PSCAD/EMTDC and MATLAB/SIMULINK environments, and experiments on a 7-level cascaded H-bridge converter.

SOFTWARE: MATLAB/SIMULINK

 BLOCK DIAGRAM:

Fig. 1 DVR strcuctures

a Conventional DVR

b CHB-based DVR

EXPECTED SIMULATION RESULTS

   

Fig. 2 Three-phase voltage sag

a Network voltage

b Injected voltage by the DVR

c Load-side voltage

Fig. 3 Voltages of the DC link capacitors

Fig. 4 Unbalanced voltage sag (a 20% voltage sag on phase A)

a Source voltage

b Injected voltage by the DVR

c Load-side voltage

Fig. 5 Three-phase 20% voltage sag with voltage harmonics

a Network voltage

b Injected voltage by the DVR

c Load-side voltage

CONCLUSION

This paper presented design and performance assessment of a DVR based on the voltage sag data collected from MWPI. Using a multilevel converter, the proposed DVR was capable of direct connection to the medium voltage-level network without a series injection transformer. In addition, development of zero active power compensation technique helps to achieve voltage restoration goal just by the capacitors as energy storages. Due to internal losses of H-bridge cells and probable inaccuracies in measurements, voltage of DC link capacitors may become unequal, which prevents proper operation of the converter. A voltage control scheme, comprised of three separate controllers, was proposed in this paper for keeping voltage balance among the DC link capacitors within nominal range. A fast estimation method was also employed for calculation of phase and magnitude terms in an unbalanced three-phase system. This estimation method is able to recognise voltage sags in approximately half a cycle. Several simulations were performed in PSCAD/EMTDC environment to verify the performance of CHB-based DVR. Additionally, a laboratory-scale prototype of the proposed DVR was built and tested. Results of the experimental test also confirmed validity of the proposed control system.

REFERENCES

1 Chapman, D.: ‘The cost of poor power quality’ (European Copper Institute, Copper Development Association, 2001), March

2 Radmehr, M., Farhangi, S., Nasiri, A.: ‘Effects of power quality distortions on electrical drives and transformer life in paper industries’, IEEE Ind. Appl. Mag., 2007, 13, (5), pp. 38–48

3 Lamoree, J., Mueller, D., Vinett, P.: ‘Voltage sag analysis case studies’, IEEE Trans. Ind. Appl., 1994, 30, (4), pp. 1083–1089

4 Bollen, M.H.J.: ‘Understanding power quality problems: voltage sags and interruptions’ (New York, Saranarce University of Technology, 2000)

5 Ghosh, A., Ledwich, G.: ‘Power quality enhancement using custom power devices’ (Berlin, Kluwer Academic Publications, 2002)

DSTATCOM supported induction generator for improving power quality

ABSTRACT

This paper presents an implementation of sliding mode controller (SMC) along with a proportional and integral (PI) controller for a DSTATCOM (Distribution STATic COMpensator) for improving current induced power quality issues and voltage regulation of three-phase self-excited induction generator (SEIG). The use of SMC for regulating the DC link voltage of DSTATCOM offers various advantages such as reduction in number of sensors for estimating reference currents and the stable DC link voltage during transient conditions. The use of PI controller for terminal voltage control gives the error free voltage regulation in steady state conditions. The voltage regulation feature of DSTATCOM offers the advantages of single point voltage operation at the generator terminals with the reactive power compensation which avoids the saturation in the generator. Other offered advantages are balanced generator currents under any loading condition, harmonic currents mitigation, stable DC link voltage and the reduced number of sensors. The SMC algorithm is successfully implemented on a DSTATCOM employed with a three-phase SEIG feeding single phase or three phase loads. The performance of the proposed control algorithm is found satisfactory for voltage regulation and mitigation of power quality problems like reactive power compensation, harmonics elimination, and load balancing under nonlinear/linear loads.

SOFTWARE: MATLAB/SIMULINK

SCHEMATIC DIAGRAM:

Fig. 1 Configuration of DSTATCOM supported induction generator

a Schematic diagram of induction generator supported by VSC-based DSTATCOM

CONTROL DIAGRAM:

b Control algorithm of DSTATCOM for estimation of reference currents using SMC

with PI controller

EXPECTED SIMULATION RESULTS

Fig. 2 Simulation results of DSTATCOM

a Performance of DSTATCOM under three-phase and single-phase non-linear load

b, c Harmonic content of load current ila and generator current

 CONCLUSION

A DSTATCOM supported induction generator has been implemented with the SMC with PI control algorithm for mitigating the power quality problems and it has enhanced the active power capability of the generator. The SMC has been verified for the dynamics in the DC-link voltage and found robust and acceptably fast to avoid large variations in DC-link voltage. Moreover, from the experimental results it has been inferred that the sliding mode control with PI controller algorithm has been found capable of meeting various functionalities of DSTATCOM such as voltage regulation, source currents balancing, harmonics mitigation, and reactive power compensation.

REFERENCES

1 Bansal, R.C.: ‘Three phase self-excited induction generators: an overview’, IEEE Trans. Energy Convers., 2005, 20, (2), pp. 292–299

2 Murthy, S.S., Singh, B., Gupta, S., et al.: ‘General steady-state analysis of three-phase self-excited induction generator feeding three-phase unbalanced load/ single-phase load for stand-alone applications’, IEE Proc. Gener. Transm. Distrib., 2003, 150, (1), pp. 49–55

3 Rai, H., Tandan, A., Murthy, S.S., et al.: ‘Voltage regulation of self-excited induction generator using passive elements’. Proc. IEEE Int. Conf. Electric Machines and Drives, September 1993, pp. 240–245

4 Singh, B., Shilpakar, L.: ‘Analysis of a novel solid state voltage regulator for a self-excited induction generator’, IEE Proc. Gener. Transm. Distrib., 1998, 145, (6), pp. 647–655

5 Singh, B., Murthy, S.S., Gupta, S.: ‘A solid state controller for self-excited induction generator for voltage regulation, harmonic compensation and load balancing’, J. Power Electron., 2005, 5, (2), pp. 109–119

MPPT With Single DC–DC Converter and Inverter for Grid-Connected Hybrid Wind-Driven PMSG–PV System

 ABSTRACT:

A new topology of a hybrid distributed generator based on photovoltaic and wind-driven permanent magnet synchronous generator is proposed. In this generator, the sources are connected together to the grid with the help of only a single boost converter followed by an inverter. Thus, compared to earlier schemes, the proposed scheme has fewer power converters. A model of the proposed scheme in the d − q-axis reference frame is developed. Two low-cost controllers are also proposed for the new hybrid scheme to separately trigger the dc–dc converter and the inverter for tracking the maximum power from both sources. The integrated operations of both proposed controllers for different conditions are demonstrated through simulation and experimentation. The steady-state performance of the system and the transient response of the controllers are also presented to demonstrate the successful operation of the new hybrid system. Comparisons of experimental and simulation results are given to validate the simulation model.

KEYWORDS:

1.      Grid-connected hybrid system

2.      Hybrid distributed generators (DGs)

3.      Smart grid

4.      Wind-driven PMSG–PV

SOFTWARE: MATLAB/SIMULINK

 BLOCK DIAGRAM:

Fig. 1. Proposed DG system based on PMSG–PV sources.

EXPECTED SIMULATION RESULTS:

Fig. 2. DC link steady-state waveforms. (a) Experimental (voltage—50 V/div, current—10 A/div, and time—500 ms/div). (b) Simulated (voltage—20 V/div, current—5 A/div, and time—500 ms/div.

Fig. 3. Steady-state grid voltage and current waveforms. (a) Experimental (voltage—50 V/div, current—10 A/div, and time—20 ms/div). (b) Simulated (voltage—50 V/div, current—5 A/div, and time— 20 ms/div).

Fig.4. Transient response for a step change in PMSG shaft speed. (a) Changes in rectifier output voltage and duty cycle of the boost converter. (b) Changes in dc-link voltage and current. (c) Changes in grid current.

CONCLUSION:

A new reliable hybrid DG system based on PV and wind driven PMSG as sources, with only a boost converter followed by an inverter stage, has been successfully implemented. The mathematical model developed for the proposed DG scheme has been used to study the system performance in MATLAB. The investigations carried out in a laboratory prototype for different irradiations and PMSG shaft speeds amply confirm the utility of the proposed hybrid generator in zero-net-energy buildings. In addition, it has been established through experimentation and simulation that the two controllers, digital MPPT controller and hysteresis current controller, which are designed specifically for the proposed system, have exactly tracked the maximum powers from both sources. Maintenance-free operation, reliability, and low cost are the features required for the DG employed in secondary distribution systems. It is for this reason that the developed controllers employ very low cost microcontrollers and analog circuitry. Furthermore, the results of the experimental investigations are found to be matching closely with the simulation results, thereby validating the developed model. The steady state waveforms captured at the grid side show that the power generated by the DG system is fed to the grid at unity power factor. The voltage THD and the current THD of the generator meet the required power quality norms recommended by IEEE. The proposed scheme easily finds application for erection at domestic consumer sites in a smart grid scenario.

REFERENCES:

[1] J. Byun, S. Park, B. Kang, I. Hong, and S. Park, “Design and implementation of an intelligent energy saving system based on standby power reduction for a future zero-energy home environment,” IEEE Trans. Consum. Electron., vol. 59, no. 3, pp. 507–514, Oct. 2013.

[2] J. He, Y. W. Li, and F. Blaabjerg, “Flexible microgrid power quality enhancement using adaptive hybrid voltage and current controller,” IEEE Trans. Ind. Electron., vol. 61, no. 6, pp. 2784–2794, Jun. 2014.

[3] W. Li, X. Ruan, C. Bao, D. Pan, and X. Wang, “Grid synchronization systems of three-phase grid-connected power converters: A complexvector- filter perspective,” IEEE Trans. Ind. Electron., vol. 61, no. 4, pp. 1855–1870, Apr. 2014.

[4] C. Liu, K. T. Chau, and X. Zhang, “An efficient wind-photovoltaic hybrid generation system using doubly excited permanent-magnet brushless machine,” IEEE Trans. Ind. Electron, vol. 57, no. 3, pp. 831–839, Mar. 2010.

[5] S. A. Daniel and N. A. Gounden, “A novel hybrid isolated generating system based on PV fed inverter-assisted wind-driven induction generators,” IEEE Trans. Energy Convers., vol. 19, no. 2, pp. 416–422, Jun. 2004.

A Study on Anti-Islanding Detection Algorithms for Grid-Tied Photovoltaic Systems

ABSTRACT

 This study analyzes various anti-islanding (AI) protection relays when the islanding condition of Grid-Tied PV (photovoltaic) System appears at the Point of Common Coupling (PCC) between the PV Solar Power System and the power grid. The main purpose of the study is to determine the performance of several AI prevention schemes in detecting the presence of an island, by monitoring the detection time of the islanding condition through different methods. The devices used to implement the methods include over-current and under-current (OI/UI) relays, over-voltage and under-voltage (OV/UV) relays, over-frequency and under-frequency (OF/UF) relays, rate of change of frequency (ROCOF) and Vector Shift relays. The protection was tested in case of complete disconnection of the PV system from the electric power grid and also in case of various grid faults.

SOFTWARE: MATLAB/SIMULINK

CIRCUIT DIAGRAM:

Fig. 1. Simulink model of the 100kW Grid-Connected PV Array

EXPECTED SIMULATION RESULTS

   

                                               Fig.2: Output results of boost converter

Fig. 3. The output result of dc link voltage (V DC) in VSC

Fig. 4. Id and Iq currents (pu) of VSC Control

Fig. 5. The Voltage between phase A and phase B of VSC

Fig. 6. Simulation result in 20kV measurement point of utility grid.

Fig. 7. The RMS value of voltage in PCC.

Fig. 8. The RMS value of current in PCC.

Fig. 9. The output result of frequency in PCC.

      

CONCLUSION :

This paper studies and compares different AI detection techniques such as passive AI prevention by standard protection schemes: OI/UI, OV/UV, OF/UF, as well as ROCOF and Vector Shift in case of a 100kW Grid-Connected PV Array. The PV System is completely disconnected from EPS and continues to energize a 20kV utility grid at 50Hz, and respectively various grid faults occurs at 5km away from the PCC of the PV System. The effectiveness of different AI detection algorithms is tested and the impact on network fault conditions and relays behavior during islanding is studied. From the results provided by the performed Matlab/Simulink simulations, it was observed that using traditional relays for islanding detection such as the OC or UV resulted

in significantly better performance in respect to detection time of islanding conditions. The ROCOF and Vector Shift relays have a detection time comparable with frequency relays. However, if the ROCOF threshold is exceeded, the formation of an island is quickly detected. The terminal voltage of PV inverter needs to exceed a certain threshold when the frequency is not stabilized by VSC. The UC relay failed entirely to detect the islanding in both analyzed cases. The effects of unintentional islanding were observed from simulation of transient grid faults on a power distribution network. The protection equipment needs to distinguish between islanding event and grid faults. The Grid-Tied PV System protections should detect the fault and trip before islanding occurs as a result of the opening of the circuit breaker in response to a downstream fault. In order to minimize these effects and to perform according to the. international standards, the AI relays have to be inserted at the points where islanding conditions may occur. The theoretical simulation results are useful to select these points and design the AI protection devices for Grid-Tied PV Systems.

REFERENCES

[1] D. Rekioua and E. Matagne, Optimization of Photovoltaic Power Systems, Modelization, Simulation and Control. Springer, 2012.

[2] IEEE Std 1547-2003, Standard for Interconnecting Distributed Resources with Electric Power Systems, IEEE, 2003.

[3] R. Teodorescu, M. Liserre and P. Rodríguez, Grid Converters for Photovoltaic and Wind Power Systems. John Wiley & Sons, Ltd., 2011.

[4] CIGRE Working Group B5.34, “The Impact of Renewable Energy Sources and Distributed Generation on Substation Protection and Automation,” CIGRE, 2010.

[5] IEEE Std 1547.2-2008, IEEE Application Guide for IEEE Std 1547™, IEEE Standard for Interconnecting Distributed Resources with Electric Power Systems, IEEE, 2008